How the Bottle Kiln works........

The hovel (outer 'skin') of the
kiln at the Dudson pottery in Hanley

The most visible outer part, which is bottle shaped is known as the HOVEL and can be a variety of shapes and sizes, it can be up to seventy feet tall.

The HOVEL acts as a chimney; taking away the smoke, creating air flow and protecting the oven inside from the weather and uneven draughts.
 

---

The outer hovel with the inner kiln visible through the door and openings

this kiln (oven) is in a range (inside the works) with only the top of the bottle
protruding through the roof
The 'bonts' are clearly visible running round the oven
around the base are the firemouths

The inner part is the kin proper. It is a round structure with a domed roof, the CROWN, and its wall are approximately one foot thick.

Iron bands known as BONTS, set about twelve inches apart, run right round the circular oven to strengthen it as it expands and contracts during the firing.
 

---

A doorway, the CLAMMINS or WICKET, surrounded by a stout iron frame and just large enough for a man with a SAGGAR on his head to pass through , is built into the kiln.
 

---

inside the kiln are a number of small chimneys - a 'bag'

Around the base of the oven are FIREMOUTHS - the exact number depends on the size of the oven, - in which fires are let for the firing. Inside the oven directly above each FIREMOUTH is a BAG, this is a small firebrick chimney, the purpose of which is to direct the flames from the fires below into the oven and protect the SAGGARS nearby.

The firemouths and underneath the flues

Underneath the floor of the kiln, FLUES, which lead from each FIREMOUTH, distribute heat throughout the interior.
In the centre of the kiln floor is the WELL HOLE over which SAGGARS, with their bottoms knocked out, are placed. This forms a chimney to allow the smoke to escape. This is the PIPE BUNG.

On average, the bottle ovens were fired once a week. A BISCUIT (first) firing took three days and a GLOST (second) firing took two days. It required about fifteen tons of coal to fire one bottle oven once, and almost half the heat generated would go up the bottle shaped chimney as smoke.

"It's a fine day if you can see the other side of the road"
 

The smoke, emerging sixty feet up, would eddy and curl down onto the buildings and street, even entering workshops and houses through ill-fitting windows and half open doors, so that the air became terribly polluted.

In Longton the town with the greatest number of bottle ovens, it used to be said, "It's a fine day if you can see the other side of the road", and when the bottle ovens were firing it was almost impossible to see your hand held in front of your face.

Fires were let in the FIREMOUTHS

batting a brick kiln

After placing the CLAMMINS (the entrance to the oven) was blocked up with bricks and sand and the oven was then ready to fire. Fires were let in the FIREMOUTHS and BATTED - that is, coal was loaded onto the fires - at intervals of about four hours.

In the early stages of firing the temperature was kept low while the moisture in the ware was driven out. This was known as SMOKING .

After about 48 hours, the maximum temperature (between 1000� C and 1250� C) was achieved and this was maintained for approximately two to three hours. The fires were then left to go out. Fine control of the draught was achieved by altering the position of the DAMPERS in the CROWN.

DAMPERS are flaps made from iron and firebrick, which the fireman could operate from ground level by means of a pulley system. By opening selected DAMPERS, the draught in different sections of the oven could be increased, thus causing the fires to burn more fiercely and raising the temperature. By closing the DAMPERS the temperature could be kept steady or lowered.

When the firing was over, the CLAMMINS was broken down and the oven left to cool. As soon as it was sufficiently cool for a man to enter without being harmed by the heat, the oven was emptied or drawn.

There is evidence that men often had to enter ovens which were too hot, because the factory owner required the ware urgently. In such cases, to protect themselves to some extent, the men wore wet rags over their hands and faces.

"You'd let your fire out on your ovens and you were supposed to wait forty eight hours until It 'd go cool - ours used to be opened after twenty four hours and it would still be red hot inside it. Then men would climb on inside and they used to have five overcoats on and about three jackets wrapped around their wrists, and he'd have to lift the saggars down with his padded arms ".