Circuit switching

Circuit switching is a methodology of implementing a telecommunications network in which two network nodes establish a dedicated communications channel (circuit) through the network before the nodes may communicate. The circuit guarantees the full bandwidth of the channel and remains connected for the duration of the communication session. The circuit functions as if the nodes were physically connected as with an electrical circuit.

Circuit switching contrasts with packet switching which divides the data to be transmitted into packets transmitted through the network independently. Packet switching shares available network bandwidth between multiple communication sessions.

In circuit switching, the bit delay is constant during a connection, as opposed to packet switching, where packet queues may cause varying packet transfer delay. Each circuit cannot be used by other callers until the circuit is released and a new connection is set up. Even if no actual communication is taking place, the channel remains unavailable to other users. Channels that are available for new calls are said to be idle.

Virtual circuit switching is a packet switching technology that emulates circuit switching, in the sense that the connection is established before any packets are transferred, and packets are delivered in order.

While circuit switching is commonly used for connecting voice circuits, the concept of a dedicated path persisting between two communicating parties or nodes can be extended to signal content other than voice. Its advantage is that it provides for continuous transfer without the overhead associated with packets making maximal use of available bandwidth for that communication. The disadvantage is inflexibility; the connection and the bandwidth associated with it are reserved and unavailable for other uses.

Multiplex techniques
Circuit mode (constant bandwidth)
TDM · FDM · SDM Polarization multiplexing Spatial multiplexing (MIMO)
Statistical multiplexing (variable bandwidth)
Packet mode · Dynamic TDM FHSS · DSSS OFDMA · SC-FDM · MC-SS
Related topics
Channel access methods Media Access Control (MAC)
This box: view · talk · edit

The call

For call setup and control (and other administrative purposes), it is possible to use a separate dedicated signalling channel from the end node to the network. ISDN is one such service that uses a separate signalling channel while plain old telephone service (POTS) does not.

The method of establishing the connection and monitoring its progress and termination through the network may also utilize a separate control channel as in the case of links between telephone exchanges which use CCS7 packet-switched signalling protocol to communicate the call setup and control information and use TDM to transport the actual circuit data.

Early telephone exchanges are a suitable example of circuit switching. The subscriber would ask the operator to connect to another subscriber, whether on the same exchange or via an inter-exchange link and another operator. In any case, the end result was a physical electrical connection between the two subscribers' telephones for the duration of the call. The copper wire used for the connection could not be used to carry other calls at the same time, even if the subscribers were in fact not talking and the line was silent.

Compared to datagram packet switching

Circuit switching contrasts with packet switching which divides the data to be transmitted into small units, called packets, transmitted through the network independently. Packet switching shares available network bandwidth between multiple communication sessions.

Multiplexing multiple telecommunications connections over the same physical conductor has been possible for a long time, but nonetheless each channel on the multiplexed link was either dedicated to one call at a time, or it was idle between calls.

In circuit switching, and virtual circuit switching, a route and bandwidth is reserved from source to destination. Circuit switching can be relatively inefficient because capacity is guaranteed on connections which are set up but are not in continuous use, but rather momentarily. However, the connection is immediately available while established.

Packet switching is the process of segmenting a message/data to be transmitted into several smaller packets. Each packet is labeled with its destination and a sequence number for ordering related packets, precluding the need for a dedicated path to help the packet find its way to its destination. Each packet is dispatched independently and each may be routed via a different path. At the destination, the original message is reassembled in the correct order, based on the packet number. Datagram packet switching networks do not require a circuit to be established and allow many pairs of nodes to communicate concurrently over the same channel.

Examples of circuit-switched networks

• public switched telephone network (PSTN)
• ISDN B-channel
• Circuit Switched Data (CSD) and High-Speed Circuit-Switched Data (HSCSD) service in cellular systems such as GSM
• Datakit
• X.21 (Used in the German DATEX-L and Scandinavian DATEX circuit switched data network)

See also

• Packet switching
• Message switching
• Call (telecommunications)
• Clos network
• Time-Driven Switching
• Connection-oriented

External links

• Netheads vs Bellheads by Steve Steinberg
• University of Virginia
• RFC 3489 Some Internet Architectural Guidelines and Philopsophy