en.unionpedia.org

Chemical milling, the Glossary

Index Chemical milling

Chemical milling or industrial etching is the subtractive manufacturing process of using baths of temperature-regulated etching chemicals to remove material to create an object with the desired shape.[1]

Table of Contents

  1. 44 relations: Aluminium, Ammonia, Ammonium persulfate, Artillery, Burr (edge), Copper, Copper(II) chloride, Denatured alcohol, Elastomer, Electric charge, Electroetching, Electrostatic spray-assisted vapour deposition, Engraving, Etching, Etching (microfabrication), Ethanol, Hydrochloric acid, Hydrofluoric acid, Hydrogen peroxide, Integrated circuit, Iron(III) chloride, Keller's reagent, Lead, Machining, Magnesium, Marking out, MEMS, Methanol, Nital, Nitric acid, Numerical control, Photochemical machining, Plasma etching, Printed circuit board, Relief, Renaissance, Resist, Semiconductor, Silicon dioxide, Sodium hydroxide, Steel, Stiletto, Venetian ceruse, White lead.

  2. Electrolysis
  3. Etching

Aluminium

Aluminium (Aluminum in North American English) is a chemical element; it has symbol Al and atomic number 13.

See Chemical milling and Aluminium

Ammonia

Ammonia is an inorganic chemical compound of nitrogen and hydrogen with the formula.

See Chemical milling and Ammonia

Ammonium persulfate

Ammonium persulfate (APS) is the inorganic compound with the formula (NH4)2S2O8.

See Chemical milling and Ammonium persulfate

Artillery

Artillery are ranged weapons that launch munitions far beyond the range and power of infantry firearms.

See Chemical milling and Artillery

Burr (edge)

A burr is a raised edge or small piece of material that remains attached to a workpiece after a modification process.

See Chemical milling and Burr (edge)

Copper

Copper is a chemical element; it has symbol Cu and atomic number 29.

See Chemical milling and Copper

Copper(II) chloride

Copper(II) chloride, also known as cupric chloride, is an inorganic compound with the chemical formula.

See Chemical milling and Copper(II) chloride

Denatured alcohol

Denatured alcohol, also known as methylated spirits, metho, or meths in Australia, Ireland, New Zealand, South Africa, and the United Kingdom; and denatured rectified spirit is ethanol that has additives to make it poisonous, bad-tasting, foul-smelling, or nauseating to discourage its recreational consumption.

See Chemical milling and Denatured alcohol

Elastomer

An elastomer is a polymer with viscoelasticity (i.e. both viscosity and elasticity) and with weak intermolecular forces, generally low Young's modulus (E) and high failure strain compared with other materials.

See Chemical milling and Elastomer

Electric charge

Electric charge (symbol q, sometimes Q) is the physical property of matter that causes it to experience a force when placed in an electromagnetic field.

See Chemical milling and Electric charge

Electroetching

Electroetching is a metal etching process that involves the use of a solution of an electrolyte, an anode, and a cathode. Chemical milling and Electroetching are etching.

See Chemical milling and Electroetching

Electrostatic spray-assisted vapour deposition

Electrostatic spray-assisted vapour deposition (ESAVD) is a technique (developed by a company called IMPT) to deposit both thin and thick layers of a coating onto various substrates. Chemical milling and Electrostatic spray-assisted vapour deposition are Metalworking.

See Chemical milling and Electrostatic spray-assisted vapour deposition

Engraving

Engraving is the practice of incising a design on a hard, usually flat surface by cutting grooves into it with a burin. Chemical milling and Engraving are Metalworking.

See Chemical milling and Engraving

Etching

Etching is traditionally the process of using strong acid or mordant to cut into the unprotected parts of a metal surface to create a design in intaglio (incised) in the metal. Chemical milling and Etching are chemical processes and Metalworking.

See Chemical milling and Etching

Etching (microfabrication)

Etching is used in microfabrication to chemically remove layers from the surface of a wafer during manufacturing. Chemical milling and Etching (microfabrication) are etching.

See Chemical milling and Etching (microfabrication)

Ethanol

Ethanol (also called ethyl alcohol, grain alcohol, drinking alcohol, or simply alcohol) is an organic compound with the chemical formula.

See Chemical milling and Ethanol

Hydrochloric acid

Hydrochloric acid, also known as muriatic acid or spirits of salt, is an aqueous solution of hydrogen chloride (HCl).

See Chemical milling and Hydrochloric acid

Hydrofluoric acid

Hydrofluoric acid is a solution of hydrogen fluoride (HF) in water.

See Chemical milling and Hydrofluoric acid

Hydrogen peroxide

Hydrogen peroxide is a chemical compound with the formula.

See Chemical milling and Hydrogen peroxide

Integrated circuit

An integrated circuit (IC), also known as a microchip, computer chip, or simply chip, is a small electronic device made up of multiple interconnected electronic components such as transistors, resistors, and capacitors.

See Chemical milling and Integrated circuit

Iron(III) chloride

Iron(III) chloride describes the inorganic compounds with the formula (H2O)x.

See Chemical milling and Iron(III) chloride

Keller's reagent

Keller's reagent can refer to either of two different mixtures of acids. Chemical milling and Keller's reagent are etching.

See Chemical milling and Keller's reagent

Lead

Lead is a chemical element; it has symbol Pb (from Latin plumbum) and atomic number 82.

See Chemical milling and Lead

Machining

Machining is a manufacturing process where a desired shape or part is created using the controlled removal of material, most often metal, from a larger piece of raw material by cutting. Chemical milling and Machining are Metalworking.

See Chemical milling and Machining

Magnesium

Magnesium is a chemical element; it has symbol Mg and atomic number 12.

See Chemical milling and Magnesium

Marking out

Marking out or layout means the process of transferring a design or pattern to a workpiece, as the first step in the manufacturing process.

See Chemical milling and Marking out

MEMS

MEMS (micro-electromechanical systems) is the technology of microscopic devices incorporating both electronic and moving parts.

See Chemical milling and MEMS

Methanol

Methanol (also called methyl alcohol and wood spirit, amongst other names) is an organic chemical compound and the simplest aliphatic alcohol, with the chemical formula (a methyl group linked to a hydroxyl group, often abbreviated as MeOH).

See Chemical milling and Methanol

Nital

Nital is a solution of nitric acid and alcohol commonly used for etching of metals. Chemical milling and Nital are etching.

See Chemical milling and Nital

Nitric acid

Nitric acid is the inorganic compound with the formula.

See Chemical milling and Nitric acid

Numerical control

In machining, numerical control, also called computer numerical control (CNC), is the automated control of tools by means of a computer.

See Chemical milling and Numerical control

Photochemical machining

Photochemical machining (PCM), also known as photochemical milling or photo etching, is a chemical milling process used to fabricate sheet metal components using a photoresist and etchants to corrosively machine away selected areas. Chemical milling and photochemical machining are etching.

See Chemical milling and Photochemical machining

Plasma etching

Plasma etching is a form of plasma processing used to fabricate integrated circuits.

See Chemical milling and Plasma etching

Printed circuit board

A printed circuit board (PCB), also called printed wiring board (PWB), is a medium used to connect or "wire" components to one another in a circuit.

See Chemical milling and Printed circuit board

Relief

Relief is a sculptural method in which the sculpted pieces remain attached to a solid background of the same material.

See Chemical milling and Relief

Renaissance

The Renaissance is a period of history and a European cultural movement covering the 15th and 16th centuries.

See Chemical milling and Renaissance

Resist

A resist, used in many areas of manufacturing and art, is something that is added to parts of an object to create a pattern by protecting these parts from being affected by a subsequent stage in the process.

See Chemical milling and Resist

Semiconductor

A semiconductor is a material that has an electrical conductivity value falling between that of a conductor, such as copper, and an insulator, such as glass.

See Chemical milling and Semiconductor

Silicon dioxide

Silicon dioxide, also known as silica, is an oxide of silicon with the chemical formula, commonly found in nature as quartz.

See Chemical milling and Silicon dioxide

Sodium hydroxide

Sodium hydroxide, also known as lye and caustic soda, is an inorganic compound with the formula.

See Chemical milling and Sodium hydroxide

Steel

Steel is an alloy of iron and carbon with improved strength and fracture resistance compared to other forms of iron.

See Chemical milling and Steel

Stiletto

A stiletto (plural stilettos) is a specialized dagger with a long slender blade and needle-like point, primarily intended as a thrusting and stabbing weapon.

See Chemical milling and Stiletto

Venetian ceruse

Venetian ceruse or Venetian white, also known as blanc de céruse de Venise and Spirits of Saturn, was a 16th-century cosmetic used as a skin whitener.

See Chemical milling and Venetian ceruse

White lead

White lead is the basic lead carbonate 2PbCO3·Pb(OH)2.

See Chemical milling and White lead

See also

Electrolysis

Etching

References

[1] https://en.wikipedia.org/wiki/Chemical_milling

Also known as Etch techniques, Etching (chemical), Etching (industry), Etching compound, Industrial etching, Maskant.