1. i
A
Colloquium Report
On
COMPUTER PERIPHERAL
Submitted In
Partial Fulfillment of the Requirements
for the Degree of
BACHELOR OF TECHNOLOGY
in
INFORMATION TECHNOLOGY
by
ADARSH KUMAR YADAV
(Roll no.1573713002)
Under the Supervision of
Mrs. SUPRIYA MISHRA TIWARI
RAJKIYA ENGINEERINGCOLLEGE AMBEDKAR-NAGAR
to the
Faculty of Information Technology
Dr. A.P.J. ABDUL KALAM UNIVERSITY, UTTARPRADESH
LUCKNOW
May, 2017
2. ii
CERTIFICATE
This is to certify that the colloquium report entitled “Computer Peripheral”
submitted by Adarsh Kumar Yadav in partial fulfillment of the requirements for the
award of Bachelor of Technology degree in Information Technology from Rajkiya
Engineering College Ambedkarnagar, affiliated to Dr.A.P.J. Abdul Kalam University
Lucknow under my supervision during the academic session 2016-2017
SUPERVISOR
Mrs. Supriya Mishra Tiwari
Information Technology
APPROVED FOR SUBMISSION
Mr. Shobhit Kumar
(Head of Department)
Information Technology
Date:
3. iii
ABSTRACT
A computer peripheral is a device that is connected to a computer but is not part of the
core computer architecture. The core elements of a computer are the central processing
unit, power supply, motherboard and the computer case that contains those three
components. Technically speaking, everything else is considered a peripheral device.
However, this is a somewhat narrow view, since various other elements are required for a
computer to actually function, such as a hard drive and random-access memory (or RAM).
Most people use the term peripheral more loosely to refer to a device external to the
computer case. You connect the device to the computer to expand the functionality of the
system. For example, consider a printer. Once the printer is connected to a computer, you
can print out documents. Another way to look at peripheral devices is that they are
dependent on the computer system. For example, most printers can't do much on their own,
and they only become functional when connected to a computer system.
Some devices fall into more than one category. Consider a CD-ROM drive; you can use it
to read data or music (input), and you can use it to write data to a CD (output).
Peripheral devices can be external or internal. For example, a printer is an external device
that you connect using a cable, while an optical disc drive is typically located inside the
computer case. Internal peripheral devices are also referred to as integrated peripherals.
When most people refer to peripherals, they typically mean external ones.
The concept of what exactly is 'peripheral' is therefore somewhat fluid. For a desktop
computer, a keyboard and a monitor are considered peripherals - you can easily connect
and disconnect them and replace them if needed. For a laptop computer, these components
are built into the computer system and can't be easily removed.
The term 'peripheral' also does not mean it is not essential for the function of the computer.
Some devices, such as a printer, can be disconnected and the computer will keep on
working just fine. However, remove the monitor of a desktop computer and it becomes
pretty much useless.
4. iv
ACKNOWLEDGEMENT
I would like to thank respected Mrs. Supriya Mishra Tiwari and Miss. Anamika
Srivastava for giving me such a wonderful opportunity to expand my knowledge for my
own branch and giving me guidelines to present a colloquium report. It helped me a lot to
realize of what we study for.
Secondly, I would like to thank my parents who patiently helped me as i went through my
work and helped to modify and eliminate some of the irrelevant or un-necessary stuffs.
Thirdly, I would like to thank my friends who helped me to make my work more organized
and well-stacked till the end.
Next, I would thank Microsoft for developing such a wonderful tool like MS Word. It
helped my work a lot to remain error-free.
Last but clearly not the least; I would thank the almighty for giving me strength to
complete my report on time.
5. v
TABLE OF CONTENTS
Page No.
Certificate ii
Abstract iii
Acknowledgement iv
CHAPTER 1: INTRODUCTION
1.1 COMPUTER PERIPHERAL 02
CHAPTER 2: OUTPUT DEVICES
2.1 HARD COPY OUTPUT 03
2.1.1 Printer 03
2.1.2 Plotter
2.2 SOFT COPY OUTPUT 15
2.2.1 LCD Monitor 17
2.2.2 Projector 23
2.3 AUDIO OUTPUT 26
2.3.1 Speaker 26
CHAPTER 3: INPUT DEVICES
3.1 Keyboard 31
3.2 Pointer 32
3.3Scanner 33
3.4 Digital Camera 34
CHAPTER 4: STORAGE DEVICES
4.1 PRIMARY STORAGE 36
4.1.1 RAM 37
4.1.2 ROM 38
4.2 SECONDARY STORAGE 39
4.2.1 Hard Disk 39
4.2.2 Compact Disk 40
6. 1
CHAPTER 1
INTRODUCTION
A computer words comes from ‘compute’, which means ‘to calculate’.
What is computer?
omputer is an electronic device, which can deal both arithmetical and logical
operation. Even though the size, shape, performance, reliability and cost of computers
have been changing over the years. All computer systems perform the following five basic
operations for converting raw input data into useful information and presenting it to a user:
• Inputting Process of entering data and instructions into a computer system.
• Storing Saving data and instructions to make them readily available for initial or
additional processing as and when required.
• Processing Performing arithmetic operations (add, subtract, multiply, divide etc.) or
logical operations (comparisons like equal to, less than, greater than, etc.) on data to
convert them into useful information.
• Outputting Process of producing useful information or results for a user, such as printed
report or visual display.
• Controlling Directing the manner and sequence in which the above operations are
performed.
Fig 1 Basic computer Operations
C
7. 2
COMPUTER PERIPHERAL
A computer peripheral is a device that is connected to a computer but is not part of the
core computer architecture. The core elements of a computer are the central processing
unit, power supply, motherboard and the computer case that contains those three
components. Technically speaking, everything else is considered a peripheral device.
However, this is a somewhat narrow view, since various other elements are required for a
computer to actually function, such as a hard drive and random-access memory (or RAM).
Most people use the term peripheral more loosely to refer to a device external to the
computer case. You connect the device to the computer to expand the functionality of the
system. For example, consider a printer. Once the printer is connected to a computer, you
can print out documents. Another way to look at peripheral devices is that they are
dependent on the computer system. For example, most printers can't do much on their own,
and they only become functional when connected to a computer system.
Types of PeripheralDevices
There are many different peripheral devices, but they fall into three general categories:
1. Output devices, such as a monitor and a printer
2. Input devices, such as a mouse and a keyboard
3. Storage devices, such as a hard drive or flash drive
Some devices fall into more than one category. Consider a CD-ROM drive; you can use it
to read data or music (input), and you can use it to write data to a CD (output).
Peripheral devices can be external or internal. For example, a printer is an external device
that you connect using a cable, while an optical disc drive is typically located inside the
computer case. Internal peripheral devices are also referred to as integrated peripherals.
When most people refer to peripherals, they typically mean external ones.
The concept of what exactly is 'peripheral' is therefore somewhat fluid. For a desktop
computer, a keyboard and a monitor are considered peripherals - you can easily connect
and disconnect them and replace them if needed. For a laptop computer, these components
are built into the computer system and can't be easily removed.
The term 'peripheral' also does not mean it is not essential for the function of the computer.
Some devices, such as a printer, can be disconnected and the computer will keep on
working just fine. However, remove the monitor of a desktop computer and it becomes
pretty much useless.
8. 3
CHAPTER 2
OUTPUT DEVICES
Output devices perform the reverse operation of that of an input device. It supplies
information obtained from data processing to outside world. Hence, it links a computer
with its external environment. As computer work with binary code, results produced are
also in binary form. Therefore, before supplying the results to outside world, the system
must convert them to human acceptable form. Units called out put interfaces accomplish
this task. Output interfaces match the unique physical or electrical characteristics of output
devices to the requirements of an external environment.
An output unit performs following functions;
1. It accepts the results produced by a computer, which are in coded form and hence, we
cannot easily understand them.
2. It converts these coded results to human readable form. 3. It supplies the converted
results to outside world.
There are three types of output:
2.1 Hard copy output.
2.2 Soft copy output.
2.3 Audio output.
2.1 Hard Copy Output
The physical form of output is known as hard copy. In general, it refers to the recorded
information copied from a computer onto paper or some other durable surface, as
microfilm. Hard copy output is permanent and a relatively stable form of output. This type
of output is also highly portable. Paper is one of the most widely used hard copy output
media. The principal examples are printouts, whether text or graphics, form printers. There
are two types of hard copy output devices:
• Printer
• Plotter
2.1.1Printer:
A printer prints information and data from the computer on to a paper. Some printer
produces only textual information whereas others can produce graphical as well.
Printers are divided two basic categories one is Impact printer and other is Non-impact
printer.
Printer
1. Impact Printer
2 .Non-Impacts Printer
9. 4
1. Impact Printer:
Impact printers work by physically striking a head or needle against an in ribbon to
make a mark on the paper. For example:
a. Dot Matrix Printer
b. Daisy Wheel Printer
c. Drum Printer
d. Chain/Band printer
a. Dot Matrix Printer:
In the 1970s and 1980s, dot matrix impact printers were generally considered the best
combination of expense and versatility, and until the 1990s they were by far the most
common form of printer used with personal computers
Dot-matrix printers can be broadly divided into two major classes:
• Ballistic wire printers
• Stored energy printer
Dot matrix printers can either be character-based or line-based (that is, a single horizontal
series of pixels across the page), referring to the configuration of the print head.
At one time, dot matrix printers were one of the more common types of printers used for
general use — such as for home and small office use. Such printers would have either 9 or
24 pins on the print head. 24-pin print heads were able to print at a higher quality. Once the
price of inkjet printers dropped to the point where they were competitive with dot matrix
printers, dot matrix printers began to fall out of favor for general use.
Fig. 2.1Dot Matrix Mechanism Fig. 2.2 Dot Matrix Printer
10. 5
How Dot matrix printer works?
The technology behind dot matrix printing is quite simple. The paper is pressed against a
rubber-coated cylinder and is pulled forward as printing progresses. The printer consists of
an electro-magnetically driven print head, which is made up of numerous print wires. The
characters are formed by moving the electro-magnetically driven print head across the
paper, which strikes the printer ribbon situated between the paper and print head pin. As
the head stamps onto the paper through the inked ribbon, a character is produced that is
made up of these dots. These dots seem to be very small for the normal vision and appear
like solid human-readable characters.
Advantages and disadvantages of dot matrix printer
• Advantages
They are good, reliable workhorses ideal for use in situations where printed content is
more important than quality. The ink ribbon also does not easily dry out, including both the
ribbon stored in the casing as well as the portion that is stretched in front of the print head;
this unique property allows the dot-matrix printer to be used in environments where printer
duty can be rare, for instance, as with a Fire Alarm Control Panel's output.
• Disadvantages
Impact printers are usually noisy, to the extent that sound dampening enclosures are
available for use in quiet environments. They can only print low resolution graphics, with
limited color performance, limited quality and comparatively low speed. While far better
suited to printing on labels than a laser printer or an inkjet printer, they are prone to bent
pins (and therefore a destroyed print head) caused by printing a character half-on and half-
off the label; for text-only labels (i.e. mailing labels), a daisy wheel printer offers most of
the advantages of a dot matrix, with better print quality and a lesser chance of being
damaged.
b. Daisy wheel printer
Daisy wheel printing is an impact printing technology invented in 1969 by David S. Lee at
Diablo Data Systems. It uses interchangeable pre-formed type elements, each with 96
glyphs, to generate high-quality output comparable to premium typewriters such as the
IBM "Golf ball" Selectric, but three times faster. Daisy-wheel printing was used in
electronic typewriters, word processors and computer systems from 1972. By 1980 daisy-
wheel printers had become the dominant technology for high-quality print. Dot-matrix
impact or thermal printers were used where higher speed was required and poor print
quality was acceptable. Both technologies were rapidly superseded for most purposes when
dot-based printers—in particular laser printers—that could print any characters or graphics
rather than being restricted to a limited character set became able to produce output of
11. 6
comparable quality. Daisy-wheel technology is now found only in some electronic
typewriters.
How Daisy wheel printer works?
These printers have print heads composed of metallic or plastic wheels. A raised character
is placed on the tip of each of the daisy wheels ‘petals’. Each petal has an appearance of a
letter (upper case and lower case), number or punctuation mark on it. To print, the print
wheel is rotated around until the desired character is under the print hammer. The petal is
then struck from behind by the print hammer, which strikes the character, pushing it
against the ink ribbon, and onto the paper, creating the character.
Advantages and disadvantages
Advantages
Different typefaces and sizes can be used by replacing the daisy wheel. It is possible to use
multiple fonts within a document. It produces high-resolution output and more reliable
than dot matrix printers.
Disadvantages
Like all other impact printers, daisy wheel printers are noisy. It is slower and more
expensive than dot matrix. It can not print graphics.
Fig 2.3 Metal Daisy Wheel for Xerox & Diablo printers
12. 7
c. Chain printer
An early line printer that used type slugs linked together in a chain as its printing
mechanism. The chain spins horizontally around a set of hammers. When the desired
character is in front of the selected print column, the corresponding hammer hits the paper
into the ribbon and onto the character in the chain. Chain and train printers gave way to
band printers in the early 1980s. It is line printers that print one line at a time. It consists of
a metallic chain band on which all characters of the character set supported by the printer
are embossed. A standard character set may have 48, 64 or 96 characters. In order to
enhance printing speed, the characters in the character set are embossed several times on
the chain. For example, the chain of a 64 character set printer may have four sets of 64
characters each embossed on it. In this case, the chain will have altogether 256 characters
embossed on it.
How chain printer works?
The chain in the chain printer rotates at a high speed. A character is printed at a desired
print position by activating the appropriate hammer when the character embossed on the
chain passes below it. Since the character set is repeated several times on the chain, it is
not necessary to wait for the chain to make a complete revolution to position the desired
character in the correct print position.
Fig. 2.4 Chain printer Mechanism Fig. 2.5 Chain printer
Advantages and disadvantages
Advantages
It is line printers that print one line at a time. Its cost is low. It can be print multiple copy.
13. 8
Disadvantages
Like all other impact printers, chain printers are also noisy in operation and often use a
cover to reduce the noise level.
d. Drum printer
In a typical drum printer design, a fixed font character set is engraved onto the periphery of
a number of print wheels, the number matching the number of columns (letters in a line)
the printer could print. The wheels, joined to form a large drum (cylinder), spin at high
speed and paper and an inked ribbon are stepped (moved) past the print position. As the
desired character for each column passes the print position, a hammer strikes the paper
from the rear and presses the paper against the ribbon and the drum, causing the desired
character to be recorded on the continuous paper. Because the drum carrying the
letterforms (characters) remains in constant motion, the strike-and-retreat action of the
hammers had to be very fast. Typically, they were driven by voice coils mounted on the
moving part of the hammer.
How Drum printer works?
The basic of a line printer like drum printer is similar to those of a serial printer, except
that multiple hammers strike multiple type elements against the paper almost
simultaneously, so that an entire line is printed in one operation. A typical arrangement of
a drum printer involves a large rotating drum mounted horizontally and positioned in front
of a very wide, inked ribbon, which in turn is positioned in front of the paper itself. The
drum contains characters mounded onto its surface in columns around its circumference;
each column contains a complete set of characters (letters, digits, etc.) running around the
circumference of the drum. The drum spins continuously at high speed when the printer is
operating. In order to print a line, hammers positioned behind the paper ram the paper
against the ribbon and against the drum beyond it at exactly the right instant, such that the
appropriate character is printed in each column has been printed, the paper is advanced
upward so that the next line can be printed.
Advantages and disadvantages
Advantages
It is line printers that print one line at a time. Its cost is high than dot matrix printer. It can
be print multiple copies. Its speed is high than dot matrix and daisy wheel printer.
Disadvantages
Like all other impact printers, drum printers are also noisy in operation. It is very
expensive and its character fonts cannot be changed.
14. 9
Fig. 2.6 Drum printer Mechanism Fig. 2.7 Drum printer
2 Non-Impactprinter:
Non-Impact printers work by using techniques other than physically striking the
page to transfer ink onto the page. For example:
a. Laser Printer.
b. Inkjet Printer.
c. Thermal Printer.
a. Laser printer
A laser printer is a common type of computer printer that rapidly produces high quality
text and graphics on plain paper. As with digital photocopier and multifunction printer
(MFPs), laser printers employ a xerographic printing process but differ from analog
photocopiers in that the image is produced by the direct scanning of a laser beam across the
printer's photoreceptor.
History
The laser printer was invented at Xerox in 1969 by researcher Gary Starkweather, who had
an improved printer working by 1971 and incorporated into a fully functional networked
printer system by about a year later. The prototype was built by modifying an existing
xerography copier. Starkweather disabled the imaging system and created a spinning drum
with 8 mirrored sides, with a laser focused on the drum. Light from the laser would bounce
off the spinning drum, sweeping across the page as it traveled through the copier. The
hardware was completed in just a week or two, but the computer interface and software
took almost 3 months to complete.
The first commercial implementation of a laser printer was the IBM model 3800 in 1976,
used for high-volume printing of documents such as invoices and mailing labels. It is often
cited as "taking up a whole room," implying that it was a primitive version of the later
15. 10
familiar device used with a Personal computer. While large, it was designed for an entirely
different purpose. Many 3800s are still in use.
How it works
There are typically seven steps involved in the laser printing process:
1. Raster image processing
Generating the raster image data.
Each horizontal strip of dots across the page is known as a raster line or scan line. Creating
the image to be printed is done by a Raster Image Processor (RIP), typically built into the
laser printer. The source material may be encoded in any number of special page
description languages such as Adobe PostScript (PS) , HP Printer Command language
(PCL), or Microsoft XML Page Specification (XPS) , as well as unformatted text-only
data. The RIP uses the page description language to generate a bitmap of the final page in
the raster memory. Once the entire page has been rendered in raster memory, the printer is
ready to begin the process of sending the rasterized stream of dots to the paper in a
continuous stream.
2. Charging
Applying a negative charge to the photosensitive drum.
A corona wire (in older printers) or a primary charge roller projects an electrostatic charge
onto the photoreceptor (otherwise named the photoconductor unit), a revolving
photosensitive drum or belt, which is capable of holding an electrostatic charge on its
surface while it is in the dark.
An AC bias is applied to the primary charge roller to remove any residual charges left by
previous images. The roller will also apply a DC bias on the drum surface to ensure a
uniform negative potential. The desired print density is modulated by this DC bias.
3. Exposing
How the bitmap is written to the photosensitive drum.
The laser is aimed at a rotating polygonal mirror, which directs the laser beam through a
system of lenses and mirrors onto the photoreceptor. The beam sweeps across the
photoreceptor at an angle to make the sweep straight across the page; the cylinder
continues to rotate during the sweep and the angle of sweep compensates for this motion.
The stream of rasterized data held in memory turns the laser on and off to form the dots on
the cylinder. (Some printers switch an array of light emitting diode spanning the width of
the page, but these devices are not "Laser Printers".) Lasers are used because they generate
a narrow beam over great distances. The laser beam neutralizes (or reverses) the charge on
the white parts of the image, leaving a static electric negative image on the photoreceptor
16. 11
surface to lift the toner particles.
4. Developing
The surface with the latent image is exposed to toner, fine particles of dry plastic powder
mixed with carbon black or coloring agents. The charged toner particles are given a
negative charge, and are electrostatically attracted to the photoreceptor's latent image, the
areas touched by the laser. Because like charges repel, the negatively charged toner will
not touch the drum where the negative charge remains.
5. Transferring
The photoreceptor is pressed or rolled over paper, transferring the image. Higher-end
machines use a positively charged transfer roller on the back side of the paper to pull the
toner from the photoreceptor to the paper.
6. Fusing
Melting toner onto paper using heat and pressure. The paper passes through rollers in the
fuser assembly where heat (up to 200 Celsius) and pressure bond the plastic powder to the
paper.
One roller is usually a hollow tube (heat roller) and the other is a rubber backing roller
(pressure roller). A radiant heat lamp is suspended in the center of the hollow tube, and its
infrared energy uniformly heats the roller from the inside. For proper bonding of the toner,
the fuser roller must be uniformly hot.
7. Cleaning
When the print is complete, an electrically neutral soft plastic blade cleans any excess
toner from the photoreceptor and deposits it into a waste reservoir, and a discharge lamp
removes the remaining charge from the photoreceptor.
Advantages and disadvantages
Advantages
Its print quality is very good. It can print a page in a minute.
Disadvantages
It is very expensive
17. 12
Fig. 2.8 Laser printer Mechanism Fig.2.9 Laser printer
b. Inkjet printer
A printer that propels droplets of ink directly onto the medium. Today, almost all inkjet
printers produce color. Low-end inkjets use three ink colors (cyan, magenta and yellow),
but produce a composite black that is often muddy. Four-color inkjets (CMYK) use black
ink for pure black printing. Inkjet printers run the gamut from less than a hundred to a
couple hundred dollars for home use to tens of thousands of dollars for commercial poster
printers.
Inkjet Inks
The basic problem with inkjet inks are the conflicting requirements for a coloring agent
that will stay on the surface and rapid dispersement of the carrier fluid.
Desktop inkjet printers, as used in offices or at home, tend to use aqueous inks based on a
mixture of water, glycol and dyes or pigments. These inks are inexpensive to manufacture,
but are difficult to control on the surface of media, often requiring specially coated media.
Aqueous inks are mainly used in printers with thermal inkjet heads, as these heads require
water in order to perform. While aqueous inks often provide the broadest color gamut and
most vivid color, most are not waterproof without specialized coating or lamination after
printing. Most dye-based inks, while usually the least expensive, are subject to rapid fading
when exposed to light. Pigment-based aqueous inks are typically more costly but provide
much better long-term durability and Ultraviolet resistance. Inks marketed as “Archival-
quality” are usually pigment-based.
• Solvent inks: The main ingredient of these inks is Volatile Organic Compounds (VOCs),
organic chemical compounds that have high vapor processor. Color is achieved using
pigments rather than dyes for excellent fade-resistance. The chief advantage of solvent inks
is that they are comparatively inexpensive and enable printing on flexible, uncoated vinyl
substrates, which are used to produce vehicle graphics, billboards, banners and adhesive
decals. Disadvantages include the vapour produced by the solvent and the need to dispose
of used solvent. Unlike most aqueous inks, prints made using solvent-based inks are
18. 13
generally waterproof and Ultra- resistant (for outdoor use) without special over-coatings.
The high print speed of many solvent printers demands special drying equipment, usually a
combination of heaters and blowers. The substrate is usually heated immediately before
and after the print heads apply ink.
Advantages and disadvantages of inkjet printer
Inkjet advantages
Compared to earlier consumer-oriented color printers, inkjets have a number of
advantages. They are quieter in operation than impact dot matrix or daisywheel printer.
They can print finer, smoother details through higher print head resolution, and many
consumer inkjets with photographic-quality printing are widely available.
In comparison to more expensive technologies like thermal vex, dye sublimations, and
laser printer, inkjets have the advantage of practically no warm up time and lower cost per
page (except when compared to laser printers).
Inkjet disadvantages
Inkjet printers may have a number of disadvantages:
1. The ink is often very expensive. (For a typical OEM cartridge priced at $15, containing
5 ml of ink, the ink effectively costs $3000 per liter—or $8000 per gallon.) According to
the BBC (2003).
2. Many "intelligent" ink cartridges contain a micro chip that communicates the estimated
ink level to the printer; this may cause the printer to display an error message, or
incorrectly inform the user that the ink cartridge is empty. In some cases, these messages
can be ignored, but some inkjet printers will refuse to print with a cartridge that declares
itself empty, in order to prevent consumers from refilling cartridges.
Fig. 2.10 Inkjet printer Mechanism Fig. 2.11 Inkjet printer
19. 14
c. Thermal printer
A thermal printer (or direct thermal printer) produces a printed image by selectively
heating coated thermochromic paper, or thermal paper as it is commonly known, when the
paper passes over the thermal print head. The coating turns black in the areas where it is
heated, producing an image. Two-color direct thermal printers are capable of printing both
black and an additional color (often red), by applying heat at two different temperatures.
Thermal transfer printing is a related method that uses a heat-sensitive ribbon instead of
heat- sensitive paper.
Essential mechanisms
A thermal printer comprises these key components:
• Thermal head — generates heat; prints on paper
• Platen — a rubber roller that feeds paper
• Spring — applies pressure to the thermal head, causing it to contact the thermo- sensitive
paper
• Controller boards — for controlling the mechanism
In order to print, one inserts thermo-sensitive paper between the thermal head and the
platen. The printer sends an electrical current to the heating resistor of the thermal head,
which in turn generates heat in a prescribed pattern. The heat activates the thermo-sensitive
coloring layer of the thermo-sensitive paper, which manifests a pattern of color change in
response. Such a printing mechanism is known as a thermal system or direct system.
The paper is impregnated with a solid-state mixture of a dye and a suitable matrix; a
combination of a fluoran leuco dye and an octadecylphosphonic acid is an example. When
the matrix is heated above its melting point, the dye reacts with the acid, shifts to its
colored form, and the changed form is then conserved in metastable state when the matrix
solidifies back quickly enough.
Advantages and disadvantage
Advantages
Its print quality is very good. Thermal printers print faster and quieter than dot matrix
printers..
Disadvantages
Thermal printer paper is more expensive than average paper
20. 15
Fig.2.12 Thermal printer
2.1.2 PLOTTER
A plotter is a pen-based output device that is attached to a computer for making vector
graphics, that is, images created by a series of many straight lines. It is used to draw high-
resolution charts, graphs, blueprints, maps, circuit diagrams, and other line-based
diagrams. Plotters are similar to printers, but they draw lines using a pen. As a result, they
can produce continuous lines, whereas printers can only simulate lines by printing a closely
spaced series of dots. Multicolor plotters use different-colored pens to draw different
colors. Color plots can be made by using four pens ( cyan, magenta, yellow, and black )
and need no human intervention to change them. The plotter was the first output device to
print graphics and large engineering drawings.
There are two different types of plotters.
(a) Drum Plotters
(b) Flatbed Plotters
a. Drum Plotters:
In drum plotters, the paper on which the design is to be printed is placed over a drum.
These plotters consist of one or more pen that is mounted on a carriage which is
horizontally placed across the drum. The drum can rotate in either clockwise or
anticlockwise direction under the control of plotting instruction s sent by computer. In
case, a horizontal line is to be drawn, the horizontal movement of a pen is combined with
the vertical movement of a page via the drum. Moreover, plotters can draw curves by
creating a sequence of very short straight lines. In these plotters, each pen can have ink of
different color to produce multicolor designs.
In 1959, the Cal Comp Model 565 was the world's first drum plotter. It had one pen and
could handle media up to 11" wide.
Use of Drum Plotters:
Drum plotters are used to produce continuous output, such as plotting earthquake activity,
or for long graphic output, such as tall building structures.
21. 16
b. Flatbed Plotters:
Flatbed plotters consist of a stationary horizontal plotting surface on which paper is fixed.
The pen is mounted on a carriage, which can move horizontally, vertically leftwards or
rightwards to draw lines. In flatbed potters, the paper does not move, the pen-holding
mechanism provides all the motion. These plotters are instructed by the computer on the
movement of pens in the x-y coordinates on the page. These plotters are capable of
working on any standard, that is, from A4 size paper to some very big beds. The major
disadvantage of this potter is that it is a slow output device and can take hours to complete
a complex drawing.
Use of Flatbed Plotters: Depending on the size of the flatbed surface, these are used in
designing of ships, aircrafts, buildings, and so on.
How Plotters works?
The heart of the plotter is the printer head assembly, consisting of a horizontal bar and the
pen in use, attached to the dead assembly holding. The pen can be positioned horizontally
by moving the pen assembly along the bar. Vertical positioning is achieved by either
moving the bar (Flatbed plotters) or the paper (Drum plotter). Combinations of horizontal
and vertical movement are used to draw arbitrary lines and curves in a single action, in
contrast to printers, which usually scan horizontally across the page. Plotters create plots
by moving a pen under computer control over a drafting paper. The instructions that a
plotter receives from a computer consist of a color, beginning and end coordinates for a
line. When an image is to be drawn, a specially designed holder picks up a pen, and takes it
over to the start position. The pen is pushed down onto the paper and dragged over the
surface to produce straight or curved lines. If the product is to be in color, the pen is then
replaced with a new pen, the process continues until the image is complete.
Fig.2.13 First Drum Plotter Fig. 2.14 Plotters pen
22. 17
Fig.2.15 Drum & Flatbed Plotter
2.2 Soft copy output:
The electronic version of an output, which usually resides in computer memory and/or
disk, is known as soft copy. Unlike hard copy, soft copy is not permanent form of output. It
is transient and is usually displayed on the screen. This kind of output is not tangible, that
is, it cannot be touched. Soft copy output includes audio and visual form of output, which
is generated using a computer. In addition, textual or graphical information displayed on
computer monitor is also a soft copy for of output.
2.2.1Monitor:
Computer Display (Monitors)
A computer display is also called a display screen or video display terminal (VDT). A
monitor is a screen used to display the output. Images are represented on monitors by
individual dots called pixels. A pixel is the smallest unit on the screen that can be turned on
and off or made different shades. The density of the dots determines the clarity of the
images, the resolution.
• Screen resolution: This is the degree of sharpness of a displayed character or image. The
screen resolution is usually expressed as the number of columns by the number rows. A
1024x768 resolution means that it has 1024 dots in a line and 768 lines. A smaller screen
looks sharper on the same resolution. Another measure of display resolution is a dot pitch.
• Interlaced/Non-interlaced: An interlaced technique refreshes the lines of the screen by
exposing all odd lines first then all even lines next. A non-interlaced technology that is
developed later refreshes all the lines on the screen form top to bottom. The non- interlaced
method gives more stable video display than interlaced method. It also requires twice as
much signal information as interlaced technology.
There are two forms of display: Liquid crystal display (LCD) and Cathode-ray tubes
(CRTs).
23. 18
a. Liquid crystal display (LCD)
Liquid-crystal display monitor (LCD) is color sets that use LCD technology to produce
images. LCD monitor are thinner and lighter than CRTs of similar display size, and are
available in much larger sizes as well. This combination of features made LCDs more
practical than CRTs for many roles, and as manufacturing costs fell their. Eventual
dominance of the monitor market was all but guaranteed. In spite of the LCD's many
advantages over the CRT technology they displaced, LCDs also have a variety of
disadvantages as well. A number of other technologies are vying to enter the large-screen
television market by taking advantage of these weaknesses, including OLEDs, FED and
SED, but none of these have entered widespread production.
Fig. 2.16 LCD
LCD monitor produce a colored image by selectively filtering a white light. The light is
typically provided by a series of cold cathode fluorescent lamps (CCFLs) at the back of the
screen, although some displays use white or colored LEDs instead. Millions of individual
LCD shutters arranged in a grid, open and close to allow a metered amount of the white
light through. Each shutter is paired with a colored filter to remove all but the red, green or
blue (RGB) portion of the light from the original white source. Each shutter–filter pair
forms a single sub-pixel. The sub-pixels are so small that when the display is viewed from
even a short distance, the individual colors blend together to produce a single spot of color,
a pixel. The shade of color is controlled by changing the relative intensity of the light
passing through the sub-pixels. Liquid crystals encompass a wide range of (typically) rod-
shaped polymers that naturally form into thin layers, as opposed to the more random
alignment of a normal liquid. Some of these, the nematic liquid crystals, also show an
alignment effect between the layers. The particular direction of the alignment of a nematic
liquid crystal can be set by placing it in contact with an alignment layer or director, which
is essentially a material with microscopic groves in it. When placed on a director, the layer
in contact will align itself with the grooves, and the layers above will subsequently align
24. 19
themselves with the layers below, the bulk material taking on the director's alignment. In
the case of an LCD, this effect is utilized by using two directors arranged at right angles
and placed close together with the liquid crystal between them. This forces the layers to
align themselves in two directions, creating a twisted structure with each layer aligned at a
slightly different angle to the ones on either side.
Addressing sub-pixels
Fig. 2.17 Sub-pixels of LCD
A close-up (300×) view of a typical LCD display, clearly showing the sub-pixel structure.
The "notch" at the lower left of each sub-pixel is the thin-film transistor. The associated
capacitors and addressing lines are located around the shutter, in the dark areas.
In order to address a single shutter on the display, a series of
electrodes is deposited on the plates on either side of the liquid crystal. One side has
horizontal stripes that form rows; the other has vertical stripes that form columns. By
supplying voltage to one row and one column, a field will be generated at the point where
they cross. Since a metal electrode would be opaque, LCDs use electrodes made of a
transparent conductor, typically indium tin oxide. Since addressing a single shutter requires
power to be supplied to an entire row and column, some of the field always leaks out into
the surrounding shutters. Liquid crystals are quite sensitive, and even small amounts of
leaked field will cause some level of switching to occur. This partial switching of the
surrounding shutters blurs the resulting image. Another problem in early LCD systems was
the voltages needed to set the shutters to a particular twist was very low, but that voltage
was too low to make the crystals re-align with reasonable performance. This resulted in
slow response times and led to easily visible "ghosting" on these displays on fast-moving
images, like a mouse cursor on a computer screen. Even scrolling text often rendered as an
unreadable blur, and the switching speed was far too slow to use as a useful television
display.
Building a display
A typical shutter assembly consists of a sandwich of several layers deposited on two thin
glass sheets forming the front and back of the display. For smaller display sizes (under 30
inches), the glass sheets can be replaced with plastic.
The rear sheet starts with a polarizing film, the glass sheet, the active matrix components
and addressing electrodes, and then the director. The front sheet is similar, but lacks the
active matrix components, replacing those with the patterned color filters. Using a multi-
step construction process, both sheets can be produced on the same assembly line. The
liquid crystal is placed between the two sheets in a patterned plastic sheet that divides the
25. 20
liquid into individual shutters and keeps the sheets at a precise distance from each other.
History
Passive matrix LCDs first became common in the 1980s for various portable computer
roles. At the time they competed with plasma displays in the same market space. The
LCDs had very slow refresh rates that blurred the screen even with scrolling text, but their
light weight and low cost were major benefits. Screens using reflective LCDs required no
internal light source, making them particularly well suited to laptop computers.
Refresh rates were far too slow to be useful for television, but at the time there was no
pressing need for new television technologies. Resolutions were limited to standard
definition, although a number of technologies were pushing displays towards the limits of
that standard; Super VHS offered improved color saturation, and DVDs added higher
resolutions as well. Even with these advances, screen sizes over 30" were rare as these
formats would start to appear blocky at normal seating distances when viewed on larger
screens. Projection systems were generally limited to situations where the image had to be
viewed by a larger audience. Nevertheless, some experimentation with LCD televisions
took place during this period. In 1988, Sharp Corporation introduced the first commercial
LCD television, a 14" model. These were offered primarily as boutique items for
discerning customers, and were not aimed at the general market.
High-definition
It was the slow standardization of high definition television that first produced a market for
new monitor technologies. In particular, the wider 16:9 aspect ratio of the new material
was difficult to build using CRTs; ideally a CRT should be perfectly circular in order to
best contain its internal vacuum, and as the aspect ratio becomes more rectangular it
becomes more difficult to make the tubes. At the same time, the much higher resolutions
these new formats offered were lost at smaller screen sizes, so CRTs faced the twin
problems of becoming larger and more rectangular at the same time. LCDs of the era were
still not able to id-1990s the plasma display was the only real offering in the high
resolution space
Environmental effects
The production of LCD screens uses nitrogen trifluoride (NF3) as an etching fluid during
the production of the thin-film components. NF3 is a potent greenhouse gas, and its
extensive half-life may make it a potentionally harmful contributor to global warming. A
report in Geophysical Research Letters suggested that its effects were theoretically much
greater than better-known sources of greenhouse gasses like carbon dioxide. As NF3 was
not in widespread use at the time, it was not made part of the Kyoto Protocols and has been
deemed "the missing greenhouse gas." Critics of the report point out that it assumes that all
of the NF3 produced would be released to the atmosphere. In reality, the vast majority of
NF3 is broken down during the cleaning processes; two earlier studies found that only 2%
26. 21
to 3% of the gas escapes destruction after its use. Furthermore, the report failed to compare
NF3's effects with what it replaced, perfluorocarbon, another powerful greenhouse gas, of
which anywhere from 30% to 70% escapes to the atmosphere in typical use.
Comparison of LCD
• Packaging
In a CRT the electron beam is produced by heating a metal filament, which "boils"
electrons off its surface. The electrons are then accelerated and focused in an electron gun,
and aimed at the proper location on the screen using electromagnets. The majority of the
power budget of a CRT goes into heating the filament, which is why the back of a CRT-
based television is hot. Since the electrons are easily deflected by gas molecules, the entire
tube has to be held in vacuum. The atmospheric force on the front face of the tube grows
with the area, which requires ever-thicker glass. This limits practical CRTs to sizes around
30 inches; displays up to 40 inches were produced but weighed several hundred pounds,
and televisions larger than this had to turn to other technologies like rear-projection. The
lack of vacuum in an LCD television is one of its advantages; there is a small amount of
vacuum in sets using CCFL backlights, but this is arranged in cylinders which are naturally
stronger than large flat plates. Removing the need for heavy glass faces allows LCDs to be
much lighter than other technologies. For instance, the Sharp LC-42D65, a fairly typical
42- inch LCD television, weighs 55 lbs including a stand, while the late-model Sony KV-
40XBR800, a 40" 4:3 CRT weighs a massive 304 lbs without a stand, almost six times the
weight.
LCD panels, like other flat panel displays, are also much thinner than CRTs. Since the
CRT can only bend the electron beam through a critical angle while still maintaining focus,
the electron gun has to be located some distance from the front face of the television. In
early sets from the 1950s the angle was often as small as 35 degrees off-axis, but
improvements, especially computer assisted convergence, allowed that to be dramatically
improved and, late in their evolution, folded. Nevertheless, even the best CRTs are much
deeper than an LCD; the KV-40XBR800 is 26 inches deep, while the LC-42D65U is less
than 4 inches thick – its stand is much deeper than the screen in order to provide stability.
• Efficiency
LCDs are relatively inefficient in terms of power use per display size, because the vast
majority of light that is being produced at the back of the screen is blocked before it
reaches the viewer. To start with, the rear polarizer filters out over half of the original un-
polarized light. Examining the image above, you can see that a good portion of the screen
area is covered by the cell structure around the shutters, which removes another portion.
After that, each sub-pixel's color filter removes the majority of what is left to leave only
the desired color. Finally, to control the color and luminance of a pixel as a whole, the light
has to be further absorbed in the shutters. 3M suggests that, on average, only 8 to 10% of
the light being generated at the back of the set reaches the viewer. For these reasons the
backlighting system has to be extremely powerful. In spite of using highly efficient
27. 22
CCFLs, most sets use several hundred watts of power, more than would be required to
light an entire house with the same technology. As a result, LCD televisions end up with
overall power usage similar to a CRT of the same size. Using the same examples, the KV-
40XBR800 draws 245 W, while the LC-42D65 is only slightly better, at 235 W. Plasma
displays are worse; the best are on par with LCDs, but typical sets draw much more.
Modern LCD sets have attempted to address the power use through a process known as
"dynamic lighting" (originally introduced for other reasons, see below). This system
examines the image to find areas that are darker, and reduces the backlighting in those
areas. CCFLs are long cylinders that run the length of the screen, so this change can only
be used to control the brightness of the screen as a whole, or at least wide horizontal bands
of it. This makes the technique suitable only for particular types of images, like the credits
at the end of a movie. Sets using LEDs are more distributed, with each LED lighting only a
small number of pixels, typically a 16 by 16 patch. This allows them to dynamically adjust
brightness of much smaller areas, which is suitable for a much wider set of images.
• Image quality
Early LCD sets were widely derided for their poor overall image quality, most notably the
ghosting on fast-moving images, poor contrast ratio, and muddy colors. In spite of many
predictions that other technologies would always beat LCDs, massive investment in LCD
production and manufacturing has addressed many of these concerns.
• Contrast ratio
Even in a fully switched-off state, liquid crystals allow some light to leak through the
shutters. This limits their contrast ratios to about 1600:1 on the best modern sets, when
measured using the ANSI measurement (ANSI IT7.215-1992). Manufacturers often quote
the "Full On/off" contrast ratio instead, which is about 25% greater for any given set. This
lack of contrast is most noticeable in darker scenes; in order to display a color close to
black; the LCD shutters have to be turned to almost full opacity, limiting the number of
discrete colors they can display. This leads to "posterizing" effects and bands of discrete
colors that become visible in shadows. Which is why many reviews of LCD TV’s mention
the “shadow detail”? For contrast, the highest-end LCD TVs offer regular contrast ratios of
5000:1 and the highest-end plasma displays offer regular contrast ratios as high as
40,000:1. Canon's prototype 55" SED offered a 50,000:1 contrast ratio. Since the total
amount of light reaching the viewer is a combination of the backlighting and shuttering,
modern sets can use "dynamic backlighting" to improve the contrast ratio and shadow
detail. If a particular area of the screen is dark, a conventional set will have to set its
shutters close to opaque to cut down the light. However, if the backlighting is reduced by
half in that area, the shuttering can be reduced by half, and the number of available
shuttering levels in the sub-pixels doubles. This is the main reason high-end sets offer
dynamic lighting (as opposed to power savings, mentioned earlier), allowing the contrast
ratio across the screen to be dramatically improved. While the LCD shutters are capable of
producing about 1000:1 contrast ratio, by adding 30 levels of dynamic backlighting this is
improved to 30,000:1.
28. 23
• Color gamut
Color on an LCD television is produced by filtering down a white source and then
selectively shuttering the three primary colors relative to each other. The accuracy and
quality of the resulting colors are thus dependent on the backlighting source and its ability
to evenly produce white light. The CCFLs used in early LCD televisions were not
particularly white, and tended to be strongest in greens. Modern backlighting has improved
this, and sets commonly quote a color space covering about 75% of the NTSC 1953 color
gamut. Using white LEDs as the backlight improves this further.
2.2.2 Projector
Fig 2.18 movie projector
A movie projector is an opto-mechanical device for displaying moving pictures by
projecting them on a projection screen. Most of the optical and mechanical elements,
except for the illumination and sound devices, are present in movie cameras.
Physiology
According to the theory of persistence of vision, the perceptual processes of the brain and
the retina of the human eye retains an image for a brief moment of time. This theory is said
to account for the illusion of motion which results when a series of film images is
displayed in quick succession, rather than the perception of the individual frames in the
series.
The frequency at which flicker becomes invisible is called the flicker fusion threshold, and
is dependent on the level of illumination. Generally, the frame rate of 16 frames per second
(frame/s) is regarded as the lowest frequency at which continuous motion is perceived by
humans. (Interestingly this threshold varies across different species; a higher proportion of
rod cells in the retina will create a higher threshold level.)
It is possible to view the black space between frames and the passing of the shutter by the
following technique:
29. 24
Since the birth of sound film, virtually all film projectors in commercial movie theaters
project at a constant speed of 24 frames. This speed was chosen for financial and technical
reasons. When Warner Bros. and Western Electric were trying to find the proper projection
speed for the new sound pictures, Western Electric went to the Warner Theater in LA and
noted the AVERAGE speed at which films were projected there. They set that as the sound
seed at which a satisfactory reproduction and amplification of sound could be conducted.
Principles of operation
Fig 2.19 Kinoton FP30ST movie projector, with parts labeled.
Projection elements
As in a slide projector there are essential optical elements:
Light source
Incandescent lighting and even limelight were the first light sources used in film
projection. In the early 1900s up until the late 1960s, carbon arc lamps were the source of
light in the almost all theaters in the world.
The Xenon arc lamp was introduced in Germany in 1957 and in the US in 1963. After film
platters became commonplace in the 1970s, Xenon lamps became the most common light
source, as they could stay lit for extended periods of time, whereas a carbon rod used for a
carbon arc could last for an hour at the most.
Most lamp houses in a professional theatrical setting produce sufficient heat to burn the
film should the film remain stationary for more than a fraction of a second. Because of this,
care must be taken in inspecting a film so that it should not break in the gate and be
30. 25
damaged, particularly inflammable cellulose nitrate film stock.
Reflector and condenser lens
A curved reflector redirects light that would otherwise be wasted toward the condensing
lens.
A positive curvature lens concentrates the reflected and direct light toward the film gate.
Douser
A metal or asbestos blade which cuts off light before it can get to the film. The douser is
usually part of the lamphouse, and may be manually or automatically operated. Some
projectors have a second, electrically-controlled douser that is used for changeovers
(sometimes called a "changeover douser" or "changeover shutter"). Some projectors have a
third, mechanically-controlled douser that automatically closes when the projector slows
down (called a "fire shutter" or "fire douser"), to protect the film if the projector stops
while the first douser is still open. Dousers protect the film when the lamp is on but the
film is not moving, preventing the film from melting from prolonged exposure to the direct
heat of the lamp. It also prevents the lens from scarring or cracking from excessive heat.
Film gate and single image
A single image of the series of images comprising the movie is positioned and held flat
within an aperture called the gate. The gate also provides a slight amount of friction so that
the film does not advance or retreat except when driven to advance the film to the next
image.
Shutter
A commonly-held misconception is that film projection is simply a series of individual
frames dragged very quickly past the projector's intense light source; this is not the case. If
a roll of film were merely passed between the light source and the lens of the projector, all
that would be visible on screen would be a continuous blurred series of images sliding
from one edge to the other. It is the shutter that gives the illusion of one full frame being
replaced exactly on top of another full frame. A rotating petal or gated cylindrical shutter
interrupts the emitted light during the time the film is advanced to the next frame. The
viewer does not see the transition, thus tricking the brain into believing a moving image is
on screen. Modern shutters are designed with a flicker-rate of two times (48 Hz) or even
sometimes three times (72 Hz) the frame rate of the film, so as to reduce the perception of
screen flickering. (See Frame rate and Flicker fusion threshold.) Higher rate shutters are
less light efficient, requiring more powerful light sources for the same light on screen.
Mechanical sequence when image is shown twice and then advanced. Outer sprockets
rotate continuously while the frame advance sprockets are controlled by the mechanism
shown.
Imaging lens and aperture plate
A lens system with multiple optical elements directs the image of the film to a viewing
screen. Different lenses are used for different aspect ratios.
31. 26
Aspect ratios are controlled by the lens with the appropriate aperture plate, a piece of metal
with a precisely cut rectangular hole in the middle of equivalent aspect ratio. The aperture
plate is placed just behind the gate, and masks off any light from hitting the image outside
of the area intended to be shown. All films, even those in the standard Academy ratio, have
extra image on the frame that is meant to be masked off in the projection.
Viewing screen
In most cases this is a reflective surface which may be either aluminized (for high contrast
in moderate ambient light) or a white surface with small glass beads (for high brilliance
under dark conditions). Switchable projection screen can be switched between opaque and
clear by a safe voltage under 36V AC and is viewable from both sides. In a commercial
theater, the screen also has millions of very small, evenly spaced holes in order to allow the
passage of sound from the speakers and subwoofer which often are directly behind it.
2.3 Audio output:
Audio response is an output media, which produce either verbal or audio responses form
the computer system. These sounds are pre-recorded in a computer system. Each sound has
a unique code.
2.3.1 Speaker
Fig-2.20 3½-inch speaker Fig-2.21 High fidelity loudspeaker system
A loudspeaker (or "speaker") is an electro acoustic transducer that converts an electrical
signal into sound. The speaker pulses in accordance with the variations of an electrical
signal and causes sound waves to propagate through a medium such as air or water.
Loudspeakers (and other electro acoustic transducers) are the most variable elements in a
modern audio system and are usually responsible for most distortion and audible
differences when comparing sound systems.
Terminology
The term "loudspeaker" can refer to individual transducers (known as "drivers") or to
complete systems consisting of an enclosure incorporating one or more drivers. To
adequately reproduce a wide range of frequencies, most loudspeaker systems require more
32. 27
than one driver, particularly for high sound pressure level or maximum accuracy.
Individual drivers are used to reproduce different frequency ranges. The drivers are named
subwoofers (for very low frequencies); woofers (low frequencies); mid-range speakers
(middle frequencies); tweeters (high frequencies); and sometimes super tweeters,
optimized for the highest audible frequencies. The terms for different speaker drivers
differ, depending on the application. In two-way loudspeakers, there is no mid-range
driver, so the task of reproducing the mid-range sounds falls upon the woofer and tweeter.
Home stereos use the designation "tweeter" for high frequencies, whereas professional
audio systems for concerts may designate high frequency drivers as "HF", or "highs", or
"horns". When multiple drivers are used in a system, a "filter network", called a crossover,
separates the incoming signal into different frequency ranges and routes them to the
appropriate driver. A loudspeaker system with n separate frequency bands is described as
"n-way speakers": a two-way system will have woofer and tweeter speakers; a three-way
system is either a combination of woofer, mid-range, and tweeter, or subwoofer, woofer,
and tweeter.
History
Johann Philipp Reis installed an electric loudspeaker in his telephone in 1861; it was
capable of reproducing pure tones, but also could reproduce speech. Alexander Graham
Bell patented his first electric loudspeaker (capable of reproducing intelligible speech) as
part of his telephone in 1876, which was followed in 1877 by an improved version from
Ernst Siemens. Nikola Tesla reportedly made a similar device in 1881, but he was not
issued a patent. During this time, Thomas Edison was issued a British patent for a system
using compressed air as an amplifying mechanism for his early cylinder phonographs, but
he ultimately settled for the familiar metal horn driven by a membrane attached to the
stylus. In 1898, Horace Short patented a design for a loudspeaker driven by compressed
air; he then sold the rights to Charles Parsons, who was issued several additional British
patents before 1910. A few companies, including the Victor Talking Machine Company
and Pathé, produced record players using compressed-air loudspeakers. However, these
designs were significantly limited by their poor sound quality and their inability to
reproduce sound at low volume. Variants of the system were used for public address
applications, and more recently, other variations have been used to test space-equipment
resistance to the very loud sound and vibration levels that the launching of rockets
produces.
The modern design of moving-coil drivers was established by Oliver Lodge in (1898). The
first practical application of moving-coil loudspeakers was established by Peter L. Jensen
and Edwin Pridham, at Napa, California. Jensen was denied patents. Being unsuccessful in
selling their product to the phone companies, in 1915 they changed strategy to public
address, and named their product Magnavox. Jensen was, for years after the invention of
the loudspeaker, a part owner of The Magnavox Company.
About this same period, Walter H. Schottky invented the first ribbon loudspeaker.
33. 28
Driver types
An audio engineering rule of thumb is that individual electrodynamic drivers provide
quality performance over at most about three octaves. Multiple drivers (e.g., subwoofers,
woofers, mid-range drivers, and tweeters) are generally used in a complete loudspeaker
system to provide performance beyond three octaves.
Full-range drivers
A full-range driver is designed to have the widest frequency response possible, despite the
rule of thumb cited above. These drivers are small, typically 3 to 8 inches (7.6 to 20 cm) in
diameter to permit reasonable high frequency response, and carefully designed to give low-
distortion output at low frequencies, though with reduced maximum output level. Full-
range (or more accurately, wide-range) drivers are most commonly heard in public address
systems and in televisions, although some models are suitable for hi-fi listening. In hi-fi
speaker systems, the use of wide-range drive units can avoid undesirable interaction
between multiple drivers caused by non-coincident driver location or crossover network
issues. Fans of wide- range driver hi-fi speaker systems claim a coherence of sound, said to
be due to the single source and a resulting lack of interference, and likely also to the lack
of crossover components. Detractors typically cite wide-range drivers' limited frequency
response and modest output abilities, together with their requirement for large, elaborate,
expensive enclosures—such as transmission lines, or horns—to approach optimum
performance.
Subwoofer
A subwoofer is a woofer driver used only for the lowest part of the audio spectrum:
typically below 120 Hz. Because the intended range of frequencies in these is limited,
subwoofer system design is usually simpler in many respects than for conventional
loudspeakers, often consisting of a single speaker enclosed in a suitable box or enclosure.
To accurately reproduce very low bass notes without unwanted resonances (typically from
cabinet panels), subwoofer systems must be solidly constructed and properly braced; good
ones are typically extraordinarily heavy. Many subwoofer systems include power
amplifiers and electronic sub-filters, with additional controls relevant to low-frequency
reproduction. These variants are known as "active subwoofers". "Passive" subwoofers
require external amplification.
Woofer
A woofer is a driver that reproduces low frequencies. Some loudspeaker systems use a
woofer for the lowest frequencies, making it possible to avoid using a subwoofer.
Additionally, some loudspeakers use the woofer to handle middle frequencies, eliminating
the mid-range driver. This can be accomplished with the selection of a tweeter that
responds low enough combined with a woofer that responds high enough that the two
drivers add coherently in the middle frequencies.
Mid-range driver
A mid-range speaker is a loudspeaker driver that reproduces middle frequencies. Mid-
34. 29
range drivers can be made of paper or composite materials, or they can be compression
drivers. If the mid-range driver is cone-shaped, it can be mounted on the front baffle of a
loudspeaker enclosure, or it can be mounted at the throat of a horn for added output level
and control of radiation pattern. If it is a compression driver, it is invariably mated to a
horn.
Fig-2.22 Sound Box
To make the transition between drivers as seamless as possible, system designers have
attempted to time-align (or phase adjust) the drivers by moving one or more drivers
forward or back so that the acoustic centre of each driver is in the same vertical plane. This
may also involve tilting the face speaker back, providing a separate enclosure mounting for
each driver, or (less commonly) using electronic techniques to achieve the same effect.
These attempts have resulted in some unusual cabinet designs. The speaker mounting
scheme (including cabinets) can also cause diffraction, resulting in peaks and dips in the
frequency response. The problem is usually greatest at higher frequencies, where
wavelengths are similar to, or smaller than, cabinet dimensions. The effect can be
minimized by rounding the front edges of the cabinet, curving the cabinet itself, using a
smaller or narrower enclosure, choosing a strategic driver arrangement, or using absorptive
material around a driver.
Wiring connections
Fig 2.23
Two-way binding posts on a loudspeaker connected using banana plugs.
Efficiency vs. sensitivity
Loudspeaker efficiency is defined as the sound power output divided by the electrical
35. 30
power input. Most loudspeakers are actually very inefficient transducers; only about 1% of
the electrical energy sent by an amplifier to a typical home loudspeaker is converted to
acoustic energy. The remainder is converted to heat, mostly in the voice coil and magnet
assembly. The main reason for this is the difficulty of achieving proper impedance
matching between the acoustic impedance of the drive unit and that of the air into which it
is radiating. The efficiency of loudspeaker drivers varies with frequency as well. For
instance, the output of a woofer driver decreases as the input frequency decreases.
Digital speakers
Digital speakers have been the subject of experiments performed by Bell Labs as far back
as the 1920s. The design is simple; each bit controls a driver, which is either fully 'on' or
'off'.
There are problems with this design which have led to it being abandoned as impractical
for the present. First, for a reasonable number of bits (required for adequate sound
reproduction quality), the physical size of a speaker system becomes very large. Secondly,
due to inherent analog digital conversion issues, the effect of aliasing is unavoidable, so
that the audio output is "reflected" at equal amplitude in the frequency domain, on the
other side of the sampling frequency, causing an unacceptably high level of ultrasonic to
accompany the desired output. No workable scheme has been found to adequately deal
with this.
The term "digital" or "digital-ready" is often used for marketing purposes on speakers or
headphones, but these systems are not digital in the sense described above. They are
conventional speakers intended for use with digital sound sources (e.g., optical media,
MP3 players, etc). Rather, this is a somewhat deceptive marketing tactic, in which the
manufacturer is trying to capitalize on the popularity of digital sound recordings and
equipment.
36. 31
CHAPTER 3
INPUT DEVICES
Input devices are for too large a subject to go into great detail here, but the most
common devices are the mouse and keyboard. These devices are what
actually allow people to use computers, and are generally easy to handle
in the computer because the input usually can not come in faster than
human can think about it. In the case of the mouse and keyboard, they cannot come in
faster than you can move your hands, which for a computer is extremely slow.
Essentially input devices allow users to give instructions. Essentially input
devices allow users to give instructions to the computer or to send information to it
Some input devices are described below :-
3.1 Keyboard
A keyboard consists of a set of keys representing the alphabet and numbers. The keys
are usually laid out in QWERTY style which originates from typewriters.
How does it work?
The pressing of a key results in the generation, within the keyboard, of an 8-bit binary
word, representing the character on the pressed key. This binary pattern is usually in ASCII
code. The ASCII code for the chosen character is sent out from the keyboard using serial
data transmission. In serial data transmission, a data word is sent one bit at a time, with the
whole word being made up of a time sequence of 1's and 0's on a single line. This contrasts
with the parallel data format used on the internal buses of a processor where each bit of a
word is present at the same time on its own line.
The interface needs to store the received character from the keyboard until the processor
is ready to accept it. Since a key can be pressed at any time, the processor could be busy
performing other functions at the instant when the character is ready in the interface,
and so the data must be stored there to await transfer to the processor.
Some activities may involve the need for using a keyboard which is laid out differently
from the conventional keyboard. For example the layout may be modified to be more
ergonomic in its style. A number of different styles have been experimented with to try and
group the keys in alternative ways. Most have incorporated some form of wrist rest to
address the issue of repetitive strain injury (RSI) which is experienced by some typists. It
may also be laid out to allow access for those with some form of disability.
Fig 3.1 keyboard
37. 32
Some activities may involve the need for using a keyboard which is laid out differently
from the conventional keyboard. For example the layout may be modified to be more
ergonomic in its style. A number of different styles have been experimented with to try and
group the keys in alternative ways. Most have incorporated some form of wrist rest to
address the issue of repetitive strain injury (RSI) which is experienced by some typists. It
may also be laid out to allow access for those with some form of disability.
Capacity
Generally speaking a keyboard will not have any internal buffering. This will be carried
out at the interface which is usually in the computer.
Speed
The speed of a modified keyboard will generally be the same as a conventional keyboard.
A serial connection from the keyboard will take each keystroke and feed it to the interface
which will have a buffer.
Compatibility
Keyboards can be connected to computer systems depending upon the Operating System of
the computer and the interface used. Some keyboards use wireless technology so that the
keyboard does not need a physical connection to the computer.
3.2 Pointers:
Pointing devices have become increasingly important with the introduction of GUI and
WIMP operating systems. Originally used with graphics packages they are now used with
almost every type of package.
Pointing devices take the forms of trackerball, joystick and mouse.
Trackerballs are used on laptops or by people who may have difficulty moving their
fingers. A large ball is rotated at the top of the device and the user’s palm turns the ball and
hence the pointer on screen. (Trackerballs have mostly been replaced by trackpads on
laptops.)
Joysticks are usually related to game playing. They offer the user quick reaction to tasks
that are happening on screen. The mouse is still the most common pointer. It is still the
main input device used with computers at home and in the workplace. The mouse allows
the user to point and click on items on the screen.
How does a pointer work?
There are 2 different ways a pointer can operate. It can be a ball mechanism or optical
operation using infra-red. As the ball or light inside the mouse is moved it sends signals to
the computer moving the position of the pointer on the screen. When the pointer is in the
correct position a button on the device can be pressed to tell the computer that you wish to
access that information.
38. 33
Capacity
The mouse will feed the data straight to the processor so no buffering is required.
Speed
The speed of the pointer's movement on the screen can be controlled by the computer's
Operating System. The user can change the speed to suit his/her needs. This is a great
advantage for those who have poor eyesight.
Fig 3.2 Pointing device
Compatibility
Pointers can be connected to computer systems depending upon the Operating System of
the computer and the interface used. Some pointers use wireless technology so that the
pointer does not need a physical connection to the computer.
3.3 Scanners:
A scanner is a digitiser as it converts graphics and text information into digital form.
Modern scanners allow high resolution images to be scanned using high bit depths. This
results in image files which are very large. When using a scanner it is important to
remember to match the image to its purpose. For example if you are scanning a picture for
use in a multimedia presentation then there is no point in using a resolution of more than
about 75 dots per inch as this is all that will be displayed on the screen. Likewise, if the
screen bit depth is 16 bits then there is no point in scanning the image at 24 bits. The trade
off between storage requirements and resolution must be taken into account.
Accuracy
The accuracy of a scanner will be the main reason for purchasing that particular model.
The accuracy is dependent on the bit depth and resolution available.
Capacity
Most scanners will not have much in the way of internal buffering. They will, instead,
tend to rely on Direct Memory Access in the computer system to transfer the data quickly
to memory.
39. 34
Speed
The speed will depend more on the computer than on the scanner. As already mentioned
this is because a large amount of data must be transferred quickly to the computer's
memory. The faster this data can be transferred the faster the scanner will appear to
operate. This depends upon the bit depth, resolution and the type of interface used.
Resolution The number of dots per inch (dpi) a scanner can scan at has increased
considerably over the past 5 years. Most scanners will not offer a resolution less than
1200x1200 dpi.
Fig 3.3 Scanner
Resolution
The number of dots per inch (dpi) a scanner can scan at has increased considerably over
the past 5 years. Most scanners will not offer a resolution less than 1200x1200 dpi.
Compatibility
Scanners can be connected to computer systems depending upon the Operating System of
the computer and the interface used.
3.4. Digital Cameras:
Traditionally a camera required film. The image is focused through the lens onto the film.
When the shutter is opened light passes through the lens affecting parts of the film. Later
the film is treated in a chemical process and the final picture can be produced. With the
advent of the digital camera the film has been removed and replaced by an array of
photosensitive cells which reacts in a similar way to the film. The images are stored
electronically. This electronically stored information can then be transferred to a computer.
Accuracy
The accuracy of the camera will be dependant on the array of photosensitive sensors. The
more sensors and the smaller they are, the higher the resolution.
40. 35
Fig 4.4 Digital Camera
Capacity
This will be based on the resolution and the amount of memory in the device. The higher
the resolution the fewer the number of images which can be stored. Some will use
compression to store more images whereas others will alter the resolution. For example 36
images with 640 x 480 pixels uses the same amount of memory as 96 images with 480 x
240 pixels. Most cameras have portable memory cards or modules which can store
between 2 to 64 Mb.
Speed
A digital camera will respond at the same sorts of speeds as a conventional camera. The
length of time it takes to download the images to the computer is restricted by the speed of
the serial link and the specification of the interface.
Resolution
The number of dots per inch (dpi) a digital camera can scan at has increased considerably
over the past 5 years. Most digital cameras will not offer a resolution less than 600x600
dpi.
41. 36
CHAPTER 4
Storage Devices
All computer systems need to store data. This is done:
Temporarily while a program is running. This is stored in main memory.
Long-term to preserve programs and data while not in use. This is called backing storage.
So you can see how a computer system uses two types of memory: Main memory holds
all of the essential memory that tells your computer how to be a computer. Backing
storage holds the information that you store on backup storage devices.
Note: Memory is another term used for storage.
Types of Storage
There are four type of storage:
• Primary Storage
• Secondary Storage
• Tertiary Storage
• Off-line Storage
Fig 4.1 Linking Memory with other units
All storage devices are characterized with the following features:
• Speed
• Volatility
• Access method
• Portability
• Cost and capacity
42. 37
4.1 Primary storage
Every time you use a personal computer, the Operating System software and Applications
software that you use must be moved from the hard drive (secondary storage) to the
primary storage area called Random Access Memory (RAM). The text does an excellent
job of explaining how this storage area works.
Primary memory, also known as main memory, is an important part of a computer in
which data is stored for quick access by the computer's processor. It is made of larger
number of cells. Each cell is identified by a number called an address of the cell. Each cell
contains a piece of data.
4.1.1 RAM
When there is a requirement of the data, the cell address is used to retrieve the data. The
primary memory is organized in such a fashion that the time required to store or retrieve
data from a cell is independent of the cell addresses. That is, any location of the memory
can be chosen randomly for use. This is known as RAM.
You should be aware that the software necessary to operate your computer gets bigger and
bigger all the time. While not every instruction included in a program is moved into RAM
when you first open the program, many instructions are. The rest of the instructions are
stored in the secondary storage area (hard drives or floppy drives) until you need them. If
you never use them, they aren't moved into RAM.
If your personal computer starts to run slower and slower over time, it could be because
your programs are requiring more space in the RAM memory than you have available. The
slang term is "RAM Cram." That is, you're trying to cram too many instructions into too
little RAM and your computer just slows down as it moves instructions back and forth
between primary and secondary storage. Sometimes, instead of buying a whole new
computer, you can significantly improve the performance of your current computer by
increasing the amount of RAM. It's relatively cheap and easy to do so.
Fig 4.2 RAM
43. 38
Types of RAM
There are two basic types of the RAM. The first one is static and second is dynamic.
Dynamic RAM (DRAM) needs to be refreshed thousands of times per second. Static
RAM (SRAM) does not need to be refreshed, which makes it faster; but it is more
expensive than dynamic RAM. Both types of RAM are volatile, meaning that they
lose their contents when the power is turned off.
4.1.2 ROM
Computers also contain Read Only Memory (ROM) which are used to permanently record
data and instructions. Content of ROM can only be read. Unlike RAM, ROM retains
its content even when the computer is turned off. ROM is an ideal memory to store
critical instructions into the computers such as boot programs (programs that start
the computer system), printer driver files, and fonts. A variation of a ROM is a
Programmable Read Only Memory (PROM). PROMs are manufactured as blank chips
on which data/program can be written with a special device called a PROM
programmer. There is a special type of PROM called Erasable PROM (EPROM).
An EPROM allows the content of PROM erased by exposing it to ultraviolet
light. Instead of ultraviolet lights, electric signals are used to erase content of PROM.
Such memory is called Electrically Erasable PROM (EEPROM). EEPROMS are very
useful in manufacturing USB pen drives, cellular phones (memory card in mobile
phone), digital cameras, portable MP3 players and microSD cards.
Fig. 4.3 ROM
RAM ROM
RAM is random access memory. ROM stands for read only memory.
RAM supports reading and writing
operations into the computer.
ROM supports only read option.
44. 39
4.2 Secondary Memory:
Primary memory is generally costly and has capacity limitation, further it cannot retain
data for longer period of time. However, we need to store data and instructions for
long time so that they can be used later. For this purpose, secondary memory /secondary
storage is used. The secondary storage stores large amounts of data, instructions,
and information permanently. The popular secondary storage devices are hard disk,
compact disks (CDs), digital versatile disks (DVDs),and pen drives.
Secondary memory is not directly accessible to processor of a computer but requires use
of computer's input/output channels. Such memory is usually slower than primary memory
but it always has higher storage capacity. Further, the secondary storage memory
is non-volatile. Data remains unchanged even after Switching off the computer. Secondary
memory/storage is also known as auxiliary memory/storage.
Fig 4.4 Memory hierarchy diagram
Let us now have a look at some of the secondary storages.
4.2.1 Hard Disk:
A hard disk consists of one or more rigid metal (or glass) plates coated with a metal
oxide material that allows data to be magnetically recorded on the surface of the
platters. Figure 4.5 shows a typical hard disk. Data and instructions are recorded on the
oxide based surface by magnetising selected particles of the surface. The particles
Data and instructions are stored into it
during its operation.
Instructions are stored into it during its
manufacturing.
It is volatile memory It is non-volatile memory
45. 40
retain their magnetic orientation until that orientation is changed. Thus, hard disk
allows modification once the content is stored.
Fig 4.5 Hard disk
A hard disk platters spin at a high rate of speed, typically 5400 to 7200 revolutions per
minute (RPM). Along with one or more platters, a hard disk also contains some
read-write heads which read and write data on the disk platters.
Storage capacities of hard disks for personal computers range from 10 GB to 500 GB.
The disk provides storage area within the computer itself. Hard disk is also known as
a hard drive. Most of the hard disks are the part of computer. However, external hard
disks of different sizes and capacities (such as 350 GB, 500 GB, and 1 TB) are
also available.
4.2.2 Compact Disk (CD) :
Known by its abbreviation, CD, a compact disc is a polycarbonate with one or more metal
layers capable of storing digital information. The most prevalent types of compact discs are
those used by the music industry to store digital recordings and CD-ROMs used to
store computer data. Both of these types of compact disc are read-only, which means that
once the data has been recorded onto them, they can only be read, or played.
A compact disk (CD) is also called an optical disc. It is a flat, round, and portable storage
medium that is usually 4.75 inches in diameter. You might have seen the audio CD for
music. CD can contain other types of data such as text, graphics, and video. The typical
capacity of a CD is 650 MB of data.
Fig 4.6 Compact Disk
Unlike hard disk, CD supports optical storage. Here, data is burned into the storage
medium using beams of laser light. The burns form patterns of small pits in the
disk surface to represent data. The pits on optical media are permanent, so the
46. 41
data cannot be changed. Optical media are very durable, but they do not provide the
flexibility of magnetic media such as modification of data.
When a compact disc is played, the information is read by a laser and converted into sound
that represents an original audio source. The CD's storage capabilities have expanded
alongside its technology to read other data like CD-ROM for computers or DVD and Blu-
ray for video.
A standard CD typically holds 74 to 79 minutes of audio. The CD debuted in 1982 under
Philips Electronics and Sony Corporation. The basic compact disc is simple in appearance,
but consists of multiple layers. The base layer is polycarbonate plastic which holds the
digital data.
This layer is topped by an aluminum coating that serves to reflect the laser that reads the
disc's information. (In rare instances, silver or gold may be used in place of aluminum). A
clear layer of shiny acrylic protects the aluminum. The standard CD has a 12 cm diameter
and a 1.2 mm thickness. From its center outward, it consists of a spindle, a clamping ring, a
stack ring, a mirror band, an information area and the rim.
The CD's data layer is comprised of billions of tiny indentations called pits that are
invisible to the human eye. These pits are encoded with binary data (0's and 1's) that
maintain the disc's speed and sound. They also serve to control the disc player's laser. The
patterns of pits rest along tightly coiled spiral tracks followed by a laser. The reflected laser
beam hits a photodiode that converts the binary data into an electrical signal that is heard
like the original audio.
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -